# ESP Fingerprint (r503) for FHEM

[ESPHome](https://esphome.io/components/fingerprint_grow.html) based firmware for ESP32 or ESP8266 to manage and use a R503-RGB Fingerprint Reader over MQTT.

Supported features of my code:

* Control R503 LED
    * LED colors: RED, BLUE, PURPLE, GREEN, YELLOW, CYAN and WHITE
    * LED effects: BREATHING, FLASHING, ALWAYS_ON, ALWAYS_OFF, GRADUAL_ON and GRADUAL_OFF
* enroll a fingerprint to the reader
* delete fingerprint


<img src="doc/r503.gif" width="300">


# Getting started

## Config pins and effects

Set correct GPIO Pins in `fingerprintdoor.yaml`

```yaml
# -----------------------------
  # Config
  # -----------------------------
  devicename:           fingerprintdoor
  reader_rx_pin:        GPIO16
  reader_tx_pin:        GPIO17
  reader_sensor_pin:    GPIO5
  speed_flash:          "100"
  count_flash:          "4"
  speed_breath:         "75"
  count_breath:         "7"
  speed_gradual_off:    "200"
  speed_gradual_on:     "35"
```

## Wifi and MQTT
Create a `secrets.yaml`file in your project folder

```yaml
wifi_ssid: "YourSSID"
wifi_password: "YourPASS"
ota_password: "OtaPass"
mqtt_ip: "192.168.1.1"
mqtt_user: ""
mqtt_password: ""
```
## Flash to ESP
Follow this [GUIDE](https://esphome.io/guides/installing_esphome.html) to install ESPHome and flash it to your device with:

```shell
esphome run fingerprintdoor.yaml --device COM4
```
> Note: COM Port may differ, change it to your COM port
## FHEM MQTT2 device

```shell
defmod myFingerprintReader MQTT2_DEVICE fingerprintdoor
attr myFingerprintReader comment ToDo neuer Finger:\
- enroll neue ID\
- ID in userreading speichern\
- ID in Hashtable im notify eintragen (Admin oder Standard User)
attr myFingerprintReader event-on-change-reading .*
attr myFingerprintReader event-on-update-reading msg
attr myFingerprintReader setList GREEN:ALWAYS_ON,ALWAYS_OFF,BREATHING,FLASHING,GRADUAL_ON,GRADUAL_OFF fingerprintdoor/led/command {"color":"$EVTPART0","effect":"$EVTPART1","speed":150, "count":0}\
BLUE:ALWAYS_ON,ALWAYS_OFF,BREATHING,FLASHING,GRADUAL_ON,GRADUAL_OFF fingerprintdoor/led/command {"color":"$EVTPART0","effect":"$EVTPART1","speed":150, "count":0}\
RED:ALWAYS_ON,ALWAYS_OFF,BREATHING,FLASHING,GRADUAL_ON,GRADUAL_OFF fingerprintdoor/led/command {"color":"$EVTPART0","effect":"$EVTPART1","speed":150, "count":0}\
PURPLE:ALWAYS_ON,ALWAYS_OFF,BREATHING,FLASHING,GRADUAL_ON,GRADUAL_OFF fingerprintdoor/led/command {"color":"$EVTPART0","effect":"$EVTPART1","speed":150, "count":0}\
WHITE:ALWAYS_ON,ALWAYS_OFF,BREATHING,FLASHING,GRADUAL_ON,GRADUAL_OFF fingerprintdoor/led/command {"color":"$EVTPART0","effect":"$EVTPART1","speed":150, "count":0}\
CYAN:ALWAYS_ON,ALWAYS_OFF,BREATHING,FLASHING,GRADUAL_ON,GRADUAL_OFF fingerprintdoor/led/command {"color":"$EVTPART0","effect":"$EVTPART1","speed":150, "count":0}\
YELLOW:ALWAYS_ON,ALWAYS_OFF,BREATHING,FLASHING,GRADUAL_ON,GRADUAL_OFF fingerprintdoor/led/command {"color":"$EVTPART0","effect":"$EVTPART1","speed":150, "count":0}\
purple_breath fingerprintdoor/led/command {"color":"purple","effect":"breathing","speed":90, "count":0}\
light_master:noArg fingerprintdoor/led/command {"color":"BLUE","effect":"BREATHING","speed":165, "count":0}\
light_master_off:noArg fingerprintdoor/led/command {"color":"BLUE","effect":"GRADUAL_OFF","speed":165, "count":0}\
ready4finger:noArg fingerprintdoor/led/command {"color":"PURPLE","effect":"BREATHING","speed":165, "count":0}\
ready4finger_off:noArg fingerprintdoor/led/command {"color":"PURPLE","effect":"ALWAYS_OFF","speed":165, "count":0}\
custom fingerprintdoor/led/command {"color":"$EVTPART1","effect":"$EVTPART2","speed":$EVTPART3, "count":$EVTPART4}\
off:noArg fingerprintdoor/led/command {"color":"RED","effect":"ALWAYS_OFF","speed":20, "count":0}\
cancel:noArg fingerprintdoor/cancel_enroll\
enroll fingerprintdoor/enroll $EVTPART1\
delete fingerprintdoor/delete $EVTPART1\
\

attr myFingerprintReader userReadings ID1 {"Person 1"},\
ID2	{"Person 2"},\
ID3	{"Person 3"}
```

## Usage in FHEM

### Enroll new finger

Syntax:
```shell
set <fhem device name> enroll <finger ID>
```

Example:
```shell
set myFingerprint enroll 1
```

>Note: Enrollment cancel ist possible with:
```shell
set myFingerprint cancel
```

### Delete finger

Syntax:
```shell
set <fhem device name> delete <finger ID>
```

Example:
```shell
set myFingerprint delete 1
```

### Set Led color and effect
Syntax:
```shell
set <fhem device name> <color> <effect> <speed> <count>
```

Example:
```shell
set myFingerprint blue flash 120 3
```

>Note: If `<count>=0` for effect "flashing" or "breathing" will run continously and can be interrupted

# Example



## Device Readings

<img src="doc/fhem.jpg" width="200">

## Setlist 
<img src="doc/fhem2.jpg" width="200">


## Credits
[ESPHome project](https://esphome.io/)

[Helpful ESPHome tutorials](https://www.youtube.com/@Smarthomeyourself)